Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
10.1. Description of a design
10.2. Adjustment of the drive of switching off of coupling
10.3. Pumping of a hydraulic actuator of coupling
10.4. Removal of the main cylinder of a hydraulic actuator of coupling
10.5. Removal of a flexible hose of a hydraulic actuator of coupling
10.6. Removal of the working cylinder of a hydraulic actuator of coupling on the car with the engine UEPA-331
10.7. Removal of the working cylinder of a hydraulic actuator of coupling on the car with the VAZ-2106 engine
10.8. Replacement of a casing and the conducted clutch plate on the car with the engine UEPA-331
10.9. Replacement of a casing and the conducted clutch plate on the car with the VAZ-2106 engine
10:10. Removal of the mechanism of the drive of switching off of coupling on the car with the engine UEPA-331
10:11. Removal of the mechanism of the drive of switching off of coupling on the car with the VAZ-2106 engine
10:12. Councils of skilled
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










10-12-sovety-byvalykh.html

10:12. Councils of skilled

Replacement of the conducted clutch plate

On cars with the engine VAZ when replacing of the conducted clutch plate apply a special mandrel or an old main shaft of the transmission to its centering. Meanwhile, there is a way allowing to do without these devices. Only the G-shaped tubular key "10x13" having knee length with a bigger head of 70-90 mm is required. We establish the conducted disk and a casing of coupling on a flywheel and slightly nazhivlyay fastening bolts that the disk could move freely between a casing and a flywheel. Then we install the transmission. At the same time vents of its main shaft without difficulties enter a disk nave, and it samotsentrirutsya. Having fixed the transmission by bolts on an engine case, we remove a rubber cover of a clutch release fork lever and we take away a fork back (from the engine). Now through the formed window we tighten bolts of fastening of a casing the G-shaped key, as shown in the drawing. It is necessary to do it gradually, wrapping each bolt serially on one turn and turning a bent shaft.

Replacement of a fork of switching off of coupling

For replacement of the damaged fork of inclusion of coupling it is necessary to dismantle a coupling case. It is possible to act simpler. We turn off two bolts fixing the working cylinder of coupling, and we take him aside. We remove a rubber cover of a fork from a case and we take it. We cut the ends of a new fork on sharpened or a file on the plane like a wedge, as shown in the drawing. Lighting with a lamp via the hatch the release bearing, we put a fork into place, having brought its ends under a spring on the release bearing by means of a hook. It is necessary to return into place a cover, the cylinder of coupling and to adjust a free wheeling of a fork.

Installation of a fork by means of a tube

It is possible to establish a fork of switching off of coupling without removal of a case also by means of a thin plastic tube not less than 30 cm long (for example, from windscreen washer). We put on the ends of a tube pads of a spring and on them as on guides, we enter a fork on the place.


"previous page
10:11. Removal of the mechanism of the drive of switching off of coupling on the car with the VAZ-2106 engine
following page"
11. IZh-2126 transmission