Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
12.1. Description of a design
12.2. Oil replacement
12.3. Replacement of an epiploon of a main shaft
12.4. Replacement of an epiploon of a secondary shaft
12.5. Removal of the drive of a speedometer
12.6. Removal of the transmission
12.7. Removal of the forward bearing of a main shaft of the transmission
12.8. Dismantling and assembly of the transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










12-6-snyatie-korobki-peredach.html

12.6. Removal of the transmission

Work is carried out on a viewing ditch or the elevator.

We disconnect a wire of "weight" from the rechargeable battery.

We disconnect wires from the switch of lamps of a backing (see. "Replacement of the switch of lamps of a backing").

On the car with a mechanical speedometer the flexible shaft is disconnected from a reducer of its drive (see. "Removal of a flexible shaft of the drive of a speedometer"). If the car is completed with a combination of devices with an electronic spidemetr, then we disconnect the speed sensor plug (see. "Removal of the drive of a speedometer").

We turn off two bolts of fastening of the working cylinder of coupling to a coupling case (see. "Removal of the working cylinder of a hydraulic actuator of coupling on the car with the VAZ-2106 engine") also we take away the cylinder forward, without separating a hydraulic actuator.

We remove a floor casing (see. "Removal of a casing of a floor") and an air supply air duct in a back part of salon (see. "Removal of an air duct of air supply in a back part of salon").

We remove a protective cover of the drive of gear shifting and a core of the lever of gear shifting (see. "Removal and installation of the transmission on the car with the engine UEPA-331", a photo 1-3 and 10-11).

We turn off bolts of fastening of a starter to a coupling case (see. "Removal and dismantling of a starter 35.3708").

We remove cardan transfer (see. "Removal of cardan transfer").

Key "on 10" we turn off four bolts of fastening of a cover of a case of coupling.

We disconnect an arm of a reception pipe from the arm fixed on a transmission case (see. "Removal of a reception pipe on the car with the VAZ-2106 engine").

We substitute under a transmission case an adjustable emphasis (or a jack).

Cap key "on 14" we turn off two bolts of fastening of a cross-piece of a back support of the power unit to floor arms.

By head "on 19" with the cardan hinge and the extender it is turned off four bolts of fastening of a case of coupling to the block of cylinders of the engine.

Accurately we shift the transmission together with a coupling case back, bringing its main shaft out of a nave of the conducted clutch plate...

... also we remove the transmission.

At removal and installation of the transmission it is impossible to opirat a main shaft of a box on petals of a press spring of coupling that not to damage them.

We install the transmission in the return sequence. Before installation the end of a main shaft is applied a thin film of SHRUS-4 lubricant on shlitsevy. After installation of a box we regulate a free wheeling of a pusher of a fork of switching off of coupling (see. "Adjustment of the drive of switching off of coupling").


"previous page
12.5. Removal of the drive of a speedometer
following page"
12.7. Removal of the forward bearing of a main shaft of the transmission