Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
13.1. Description of a design
13.2. Lubricant of shlitsevy connection of the driveshaft
13.3. Removal of cardan transfer
13.4. Replacement of an epiploon of shlitsevy connection of a flange of the elastic coupling and shaft of the forward driveshaft
13.5. Removal of the elastic coupling
13.6. Dismantling of the cardan hinge
13.7. Replacement of an intermediate support
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










13-3-snyatie-kardannojj-peredachi.html

13.3. Removal of cardan transfer

We perform work on a viewing ditch or the elevator.

We install the gear shifting box lever in neutral situation and we lower the lever of the parking brake. Operations on dismantle of cardan transfer on cars with VAZ and Izhevsk transmissions are almost identical.

We show removal of cardan transfer on the car with the Izh-2126 transmission.

Key "on 13" we turn off two nuts of fastening of an arm of safety to a body floor...

... also we remove an arm from hairpins.

We put on a collar of worm type the elastic coupling. Diameter of a collar has to be not less than 150 mm. It is possible to manage two collars with a diameter of 60-80 mm linked with each other.

We tighten a collar on the coupling.

Cap key "on 19" we turn off a nut of a hairpin of fastening of the coupling to a transmission flange. We hold a shaft from a provorachivaniye an assembly shovel.

Turning a shaft, similarly we turn off two more nuts of fastening of the coupling to a transmission flange.

Assembly shovel we shift the coupling with its flange along shliyets of a shaft of the forward driveshaft.

Cap key "on 13" we turn off two nuts of fastening of an arm of an intermediate support to a body.

We remove an arm from hairpins.

In each opening of an arm plugs are installed:

... metal remote...

... and rubber.

Holding a cap key "on 13" a bolt of fastening of a fork of the back driveshaft to a flange of the leading gear wheel of the main transfer, Rozhkov a key of the same dimension we turn off a nut.

Similarly we turn off nuts of three more bolts and we take out them.

Having separated a flange fork of the back driveshaft and a flange of the leading gear wheel of the main transfer, we hold the back driveshaft from falling. Having shifted cardan transfer back, we remove the elastic coupling from transmission flange hairpins...

... also we remove cardan transfer.

For replacement of a sealant of shliyets of a shaft of the forward driveshaft...

... we remove it from a cylindrical corbel of a nut of fastening of a flange of a secondary shaft of the transmission.

For removal of the aligning ring of a flange of the elastic coupling from a shaft of a secondary shaft of the transmission...

... by kruglogubets it is unclenched a lock ring, we hook the screw-driver...

... also we remove it.

Hooking the aligning ring the screw-driver, we shift it from a shaft shaft.

We insert a rozhkovy key into the gap formed between end faces of a ring and a nut "on 17".

Leaning a key against a nut...

... we remove the aligning ring.

Before installation of cardan transfer...

... a tool head of the suitable size (or a pipe piece) napressovyvay on a shaft of a secondary shaft of the transmission the aligning plug.

We establish cardan transfer in the return sequence.

When replacing an intermediate support of cardan transfer or details of a back suspension bracket influencing position of the back bridge concerning a body...

... we enshrine an intermediate support on an arm of its fastening to a body in the provision "the car on wheels".

For self-installation of a support in an arm grooves are executed (it is for descriptive reasons shown on the dismantled arm).


"previous page
13.2. Lubricant of shlitsevy connection of the driveshaft
following page"
13.4. Replacement of an epiploon of shlitsevy connection of a flange of the elastic coupling and shaft of the forward driveshaft