Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
15.1. Description of a design
15.2. Angles of installation of forward wheels
15.3. Removal of a spherical support
15.4. Removal of the lever
15.5. Removal of the stabilizer of cross stability
15.6. Removal of the directing spring rack
15.7. Replacement of the hug bearing
15.8. Removal of a stretcher
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










15-2-ugly-ustanovki-perednikh-koles.html

15.2. Angles of installation of forward wheels

For ensuring stability and controllability of the car forward wheels of the car are established under certain corners concerning elements of a body and a suspension bracket. Three parameters are subject to adjustment: convergence, corner of disorder of a wheel and corner of a longitudinal inclination of an axis of turn.

Fig. 1. Corner of a longitudinal inclination of an axis of turn of a wheel

Corner of a longitudinal inclination of an axis of turn (fig. 1) Ч a corner between the vertical and the line passing through the centers of turn of a spherical support and the bearing of the top support of the directing spring rack in the plane parallel to a longitudinal axis of the car. For increase in a tilt angle of an axis of turn the top support of a rack which is originally located as shown in a photo 1, it is necessary to turn on 180 ∞ concerning an opening in a body mudguard cup (a photo 2).

At the same time the corner of a longitudinal inclination of an axis of turn will increase on 0 ∞52' (the operating procedure is described in the subsection "Removal of the Directing Spring Rack").

Corner of disorder of a wheel (fig. 2) Ч a corner between the plane of rotation of a wheel and a vertical. It is regulated by turn of the top bolt of fastening of a damping rack to a rotary fist (see. "Removal of the directing spring rack").

Fig. 2. Wheel disorder corner

Convergence of wheels (fig. 3) Ч a corner between the plane of rotation of a wheel and a longitudinal axis of the car. The convergence can also be defined as a difference of distances between zakraina ободьев, measured behind and in front of wheels at the level of their centers. The convergence is regulated by rotation of internal steering draft for lysk at the released lock-nut of an external tip of steering draft (see. "Removal of an external tip of steering draft").

Fig. 3. Convergence of wheels

Control and adjustment of angles of installation of forward wheels is recommended to be made at service station. Before adjustment it is necessary to be convinced that pressure in tires meets standard, wear of a protector of tires on the left and right wheels is approximately identical, there are no side plays in bearings of naves and elements of steering, wheels are not deformed.

Angles of installation of forward wheels

Parameter

Angles of installation of wheels

the equipped car

with a full weight

Disorder corner

1 ∞25±0 ∞30'

0 ∞45 '±0 ∞30'

Difference of corners of disorder of the right and left wheels, no more

0 ∞20'

0 ∞30'

Corner of a longitudinal inclination of an axis of turn (Custer)

2 ∞00 '±0 ∞30'

2 ∞30 '±0 ∞30'

Difference of kaster of the right and left wheels, no more

0 ∞30'

0 ∞30'

Convergence corner

0 ∞22 '±0 ∞07

0 ∞15 '±0 ∞07'

Convergence of wheels at measurement by a sliding ruler on a shoulder of 450 mm

3 мм±0,9 mm

2 мм±0,9 mm

Check of angles of installation of wheels is obligatory if replaced or repaired the knots and details of a suspension bracket influencing sizes of these corners. Because the angles of installation of forward wheels are interconnected, first of all check and regulate a corner of a longitudinal inclination of an axis of turn, then disorder and in the last turn Ч a convergence.


"previous page
15.1. Description of a design
following page"
15.3. Removal of a spherical support