Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
18.1. Description of a design
18.2. Pumping of brakes
18.3. Replacement of front brake shoes
18.4. Replacement of back brake shoes
18.5. Removal of the main brake cylinder
18.6. Removal of the vacuum amplifier of brakes and adjustment of a free wheeling of a pedal of a brake
18.7. Removal of pedal knot
18.8. Removal of the signaling device
18.9. Removal of a forward brake hose
18:10. Dismantling of the forward brake mechanism
18:11. Replacement of the back wheel cylinder
18:12. Removal of a back brake hose
18:13. Check of working capacity and adjustment of the drive of the regulator of pressure of back brakes
18:14. Removal of the regulator of pressure of back brakes and its drive
18:15. Adjustment and removal of knots of the parking brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










18-10-razborka-perednego-tormoznogo-mekhanizma.html

18:10. Dismantling of the forward brake mechanism

The forward brake mechanism is disassembled for replacement of the brake cylinder, a disk or other details at their wear, mechanical damage or corrosion.

We hang out and remove a forward wheel. We disconnect a brake hose from a tube (see. "Removal of a forward brake hose"). We turn off the lower bolt of fastening of a support with the cylinder to the directing finger (see. "Replacement of front brake shoes"). Raskontrivay the top bolt of fastening of a support to the directing finger...

... also we turn off it a cap key "on 13", if necessary holding a finger from a provorachivaniye the screw-driver.

We remove the brake cylinder with a hose and a support.

Having clamped a support in a vice with overlays of sponges from soft metal, a hexagon "on 10" we unscrew two screws of fastening of the cylinder to a support.

We remove the wheel cylinder.

Carefully we hook the screw-driver a protective cover of a finger and we remove it from a corbel of a guide of blocks.

We take out a finger together with a cover.

Cap key "on 17" we turn off two bolts of fastening of a guide of blocks to a rotary fist...

... also we remove a guide of blocks.

If it is necessary to replace only a brake disk, we do not disconnect a hydraulic actuator of the brake mechanism.

By head "on 17" with the extender it is turned off two bolts of fastening of a guide of blocks to a rotary fist...

... also we remove a support assembled with the brake cylinder, a guide and blocks.

Before an otvorachivaniye of hairpins of fastening of a brake disk we tap them the hammer in the axial direction.

By cap key "on 12" or a high head it is turned off two hairpins of fastening of a brake disk.

We remove a brake disk.

The guard of a brake is replaced only at its damage (a smyatiya or strong corrosion). If such need arose, it is necessary to remove a nave of a forward wheel (see. "Replacement of the hug bearing").

By the crosswise screw-driver it is turned off three screws of fastening of a guard of a forward brake...

... also we remove a guard.

Assembly and installation of the mechanism is carried out in the return sequence. We pump over the brake system (see. "Pumping of brakes").


"previous page
18.9. Removal of a forward brake hose
following page"
18:11. Replacement of the back wheel cylinder