Service of IZh 2126
1. General information
2. Engine UEPA-331
2.1. Description of a design
2.2. Oil replacement
2.3. Replacement of laying of a cover of a head of the block of cylinders
2.4. Check and adjustment of thermal gaps in the drive of valves
2.5. Adjustment of a tension of a chain of the drive of the camshaft
2.6. Removal of a natyazhitel of a chain
2.7. Removal of the drive of the distributor of ignition
2.8. Removal of a chain of the drive of the camshaft
2.9. Replacement of a forward epiploon of a bent shaft
2.10. Replacement of a back epiploon of a bent shaft
2.11. Replacement of the sensor of pressure of oil
2.12. Adjustment and replacement of the reducing valve of the oil pump
2.13. Removal of gear wheels of the oil pump
2.14. Removal of an inlet pipe
2.15. Removal of a final collector
2.16. Removal and dismantling of a head of the block of cylinders
2.17. Removal of support of the power unit on the car with the engine UEPA-331
2.18. Replacement of laying of the pallet of a case on the car
2.19. Removal of an oil receiver
2.20. dismantle of tsilindroporshnevy group (TsPG) on the car
2.21. Removal of the engine
2.22. Dismantling and assembly of the engine
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










2-17-snyatie-opor-silovogo-agregata-na-avtomobile-s-dvigatelem-umpo-331.html

2.17. Removal of support of the power unit on the car with the engine UEPA-331

We perform work on a viewing ditch or the elevator.

For dismantle of a pillow of the left forward support we enclose under the engine case pallet near a drain opening a wooden pro-rate and we substitute an adjustable support (or a jack).

For dismantle of a pillow of the right forward support we substitute an adjustable support (or a jack) under the right edge of the pallet of a case of the engine.

Operations on dismantle of pillows of forward support of the power unit are shown in the subsection "Removal of Support of the Power Unit on the Car with the VAZ-2106 Engine". For dismantle of a back support...

... we establish an adjustable support under a transmission case.

Key "on 13" we turn off a nut of a bolt of fastening of a pillow of a back support to a cross-piece, holding a bolt a key "on 12".

We take out a bolt and the expansion plug.

Similarly we take out the second bolt and its expansion plug.

Head "on 12" we turn off two bolts of fastening of a pillow of a back support to a transmission arm.

We remove a pillow of a back support.

If on a pillow there are cracks, gaps or peelings of rubber, replace a pillow new.

Removal of a cross-piece of a back support is shown in the subsection "Dismantling and Assembly of the Transmission".

We establish a pillow of a back support in the return sequence.


"previous page
2.16. Removal and dismantling of a head of the block of cylinders
following page"
2.18. Replacement of laying of the pallet of a case on the car