Service of IZh 2126
1. General information
2. Engine UEPA-331
2.1. Description of a design
2.2. Oil replacement
2.3. Replacement of laying of a cover of a head of the block of cylinders
2.4. Check and adjustment of thermal gaps in the drive of valves
2.5. Adjustment of a tension of a chain of the drive of the camshaft
2.6. Removal of a natyazhitel of a chain
2.7. Removal of the drive of the distributor of ignition
2.8. Removal of a chain of the drive of the camshaft
2.9. Replacement of a forward epiploon of a bent shaft
2.10. Replacement of a back epiploon of a bent shaft
2.11. Replacement of the sensor of pressure of oil
2.12. Adjustment and replacement of the reducing valve of the oil pump
2.13. Removal of gear wheels of the oil pump
2.14. Removal of an inlet pipe
2.15. Removal of a final collector
2.16. Removal and dismantling of a head of the block of cylinders
2.17. Removal of support of the power unit on the car with the engine UEPA-331
2.18. Replacement of laying of the pallet of a case on the car
2.19. Removal of an oil receiver
2.20. dismantle of tsilindroporshnevy group (TsPG) on the car
2.21. Removal of the engine
2.22. Dismantling and assembly of the engine
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










2-18-zamena-prokladki-poddona-kartera-na-avtomobile.html

2.18. Replacement of laying of the pallet of a case on the car

We perform work on a viewing ditch or the elevator.

We merge oil from the engine (see. "Oil replacement").
We remove an engine mudguard (see. "Removal of a mudguard of the engine").
We remove a forward cross-piece of a stretcher (see. "Removal of a stretcher").
We remove an antisplash guard of a case of coupling (see. "Replacement of a casing and the conducted clutch plate on the car with the engine UEPA-331").

By the Shlitsevy screw-driver it is turned off 18 screws...

... and a cap key - three nuts of hairpins of fastening of the pallet of a case to the block of cylinders of the engine (nuts are located on the right).

We turn off nuts of bolts of fastening of pillows of forward support of the power unit to arms of the block of cylinders of the engine (see. "Removal of support of the power unit on the car with the engine UEPA-331").

We substitute an adjustable emphasis under a case of coupling and we raise the power unit a little.

We separate the pallet of a case and the block of cylinders (sometimes the considerable effort for this purpose is required) and, having lowered a forward part of the pallet, we bring its back part out of space between the block of cylinders and a back cross-piece of a stretcher.

We remove the case pallet together with its sealing laying.

We clear the privalochny planes of the pallet and block of cylinders of the engine of oil and the remains of old laying. Previously we apply sealant from two parties on new laying and we install the case pallet in the return sequence. The sequence of an inhaling of screws and nuts of fastening of the pallet of a case is shown in fig. 3.

Fig. 3. Order of an inhaling of screws and nuts of fastening of the pallet of a case


"previous page
2.17. Removal of support of the power unit on the car with the engine UEPA-331
following page"
2.19. Removal of an oil receiver