Service of IZh 2126
1. General information
2. Engine UEPA-331
2.1. Description of a design
2.2. Oil replacement
2.3. Replacement of laying of a cover of a head of the block of cylinders
2.4. Check and adjustment of thermal gaps in the drive of valves
2.5. Adjustment of a tension of a chain of the drive of the camshaft
2.6. Removal of a natyazhitel of a chain
2.7. Removal of the drive of the distributor of ignition
2.8. Removal of a chain of the drive of the camshaft
2.9. Replacement of a forward epiploon of a bent shaft
2.10. Replacement of a back epiploon of a bent shaft
2.11. Replacement of the sensor of pressure of oil
2.12. Adjustment and replacement of the reducing valve of the oil pump
2.13. Removal of gear wheels of the oil pump
2.14. Removal of an inlet pipe
2.15. Removal of a final collector
2.16. Removal and dismantling of a head of the block of cylinders
2.17. Removal of support of the power unit on the car with the engine UEPA-331
2.18. Replacement of laying of the pallet of a case on the car
2.19. Removal of an oil receiver
2.20. dismantle of tsilindroporshnevy group (TsPG) on the car
2.21. Removal of the engine
2.22. Dismantling and assembly of the engine
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










2-6-snyatie-natyazhitelya-cepi.html

2.6. Removal of a natyazhitel of a chain

Natyazhitel chains is removed in case of its malfunction: adjustment of a tension of a chain does not yield result because of loss of mobility of a plunger, breakage or decrease in rigidity of a spring of a natyazhitel.

Cap key "on 12" we turn off a lock bolt of a natyazhitel.

We take out a bolt.

Hexagon "on 12" we turn off the stopper located in inflow of the top cover of the drive of the camshaft.

In the absence of a hexagon we turn off a high nut of fastening of the distributor of ignition (trying not to turn the distributor that the ignition advancing corner did not change)...

... and, having inserted it into a stopper, a cap key "on 12" we rotate a nut and we turn off a stopper.

Under a stopper there is a spring in the loaded state. Therefore, turning off a stopper, on the last rounds of a carving we hold it that the spring did not "shoot".

We remove a stopper with laying.

... also we take a spring.

By tweezers it is taken out a clamping plate of a plunger...

... and a plunger.

Mechanism of a natyazhitel of a chain.

We clear a plunger of a deposit and we oil engine. We insert it together with a clamping plate into a nest of the top cover of the drive of the camshaft so that the opening in a clamping plate coincided with an opening in a cover under a lock bolt. We roll a lock bolt so that its shaft entered an opening of a clamping plate. We insert a spring into a plunger. Pressing a hexagon on a stopper and overcoming effort of a spring, we wrap a stopper. Having turned a bent shaft of the engine in the direction of its rotation on 2-3 turns, we tighten a lock bolt.


"previous page
2.5. Adjustment of a tension of a chain of the drive of the camshaft
following page"
2.7. Removal of the drive of the distributor of ignition