Service of IZh 2126
1. General information
2. Engine UEPA-331
2.1. Description of a design
2.2. Oil replacement
2.3. Replacement of laying of a cover of a head of the block of cylinders
2.4. Check and adjustment of thermal gaps in the drive of valves
2.5. Adjustment of a tension of a chain of the drive of the camshaft
2.6. Removal of a natyazhitel of a chain
2.7. Removal of the drive of the distributor of ignition
2.8. Removal of a chain of the drive of the camshaft
2.9. Replacement of a forward epiploon of a bent shaft
2.10. Replacement of a back epiploon of a bent shaft
2.11. Replacement of the sensor of pressure of oil
2.12. Adjustment and replacement of the reducing valve of the oil pump
2.13. Removal of gear wheels of the oil pump
2.14. Removal of an inlet pipe
2.15. Removal of a final collector
2.16. Removal and dismantling of a head of the block of cylinders
2.17. Removal of support of the power unit on the car with the engine UEPA-331
2.18. Replacement of laying of the pallet of a case on the car
2.19. Removal of an oil receiver
2.20. dismantle of tsilindroporshnevy group (TsPG) on the car
2.21. Removal of the engine
2.22. Dismantling and assembly of the engine
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










2-7-snyatie-privoda-raspredelitelya-zazhiganiya.html

2.7. Removal of the drive of the distributor of ignition

We uncover the ignition distributor, without taking out high-voltage wires from its nests (see. "Removal of a cover and rotor of the distributor of ignition"). We establish cranked and distributive shaft in the provision of the end of a step of compression of the first cylinder. For this purpose we turn a bent shaft in the direction of rotation a tag on a pulley of a bent shaft so far (the second for the direction of rotation) will not be established opposite to a pin on the lower cover of the drive of the camshaft (see. "Check and adjustment of thermal gaps in the drive of valves")...

... and the tokoraznosny plate of a rotor of the distributor will not be established opposite to contact of a high-voltage wire of the first cylinder in the distributor cover (marked from above on a cover with figure "1"). We remove the ignition distributor (see. "Removal of the distributor of ignition").

Cap key "on 10" we turn off two nuts of fastening of the case of the drive of the distributor to the lower cover of the drive of the camshaft.

We take out the distributor drive from a cover nest.

We remove sealing laying.

We install the distributor drive in the return sequence. At the same time...

... we focus a roller groove, as shown in a picture.

When the gear wheel of the drive of the distributor enters gearing with the leading gear wheel of a bent shaft...

... the roller of the drive will a little turn counterclockwise, and the groove of the roller of the drive will reach such position.


"previous page
2.6. Removal of a natyazhitel of a chain
following page"
2.8. Removal of a chain of the drive of the camshaft