Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
22.1. Features of a design
22.2. Elements of system of production of the fulfilled gases
22.3. Removal of the shock-absorber of a back suspension bracket
22.4. Removal of a spring
22.5. Removal of a back lamp, replacement of lamps
22.6. Removal of plafonds of illumination of registration plate
22.7. Removal of a gas-filled emphasis of a door of a cap
22.8. Removal of the lock of a door of a cap and its drives
22.9. Removal of a door of a cap
22:10. Removal of a cap
22:11. Removal of boards of a body and their locks
23. Appendix
24. Care of a car body
 










22-4-snyatie-ressory.html

22.4. Removal of a spring

We remove a spring for replacement.

Back fastenings of both springs also disconnect at dismantle of a beam of the back bridge assembled.

We install the car on a viewing ditch or the elevator. We disconnect the lower fastening of the shock-absorber (see. "Removal of the shock-absorber of a back suspension bracket").

Cap key "on 19" we turn off four nuts of fastening of step-ladders to a plate.

We remove a plate of step-ladders.

We remove step-ladders...

... and compression buffer.

We establish an adjustable emphasis under a beam of the back bridge and we raise it on 30-50 mm over a spring.

Cap key "on 19" we turn off two nuts of a cheek of an earring...

... also we remove it.

We hook an assembly shovel a back eye of a spring...

... also we remove it from a finger.

We lower a spring on an emphasis.

We hook an assembly shovel an earring cheek with fingers...

... also we remove it.

Fingers of an earring are established in an opening of a longeron of a body and an eye of a spring via rubber plugs.

Cap key "on 19" we turn off a nut of a forward finger from spherical washers, holding a finger from a provorachivaniye a pipe key for lysk.

The same tools we turn off a nut on the other side of a finger.

We take out spherical washers.

... also we beat out a forward finger through a drift from soft metal.

We take out a finger together with the rubber plug, releasing a forward eye of a spring.

We remove a spring.

Details of fastening of a forward eye of a spring.

We establish a spring in the return sequence.

At the same time the spring has to be turned by an eye of such form to a forward part of the car...

... and such — to back.

At installation of a forward eye of a spring we insert the second rubber plug into an eye through an arm opening for spherical washers.

We replace the deformed spherical washers new.

We put spherical washers cambers outside and we establish in an arm opening.

We tighten nuts of fingers evenly, avoiding a distortion of rubber plugs.

Stacking a beam of the back bridge on a spring...

... we provide hit of a head of a coupling bolt of a spring...

... in an average opening of an arm of a beam of the back bridge.

All threaded connections are finally tightened in situation "the car on wheels".


"previous page
22.3. Removal of the shock-absorber of a back suspension bracket
following page"
22.5. Removal of a back lamp, replacement of lamps