Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
3.1. Description of a design
3.2. Oil replacement
3.3. Replacement of laying of a cover of a head of the block of cylinders
3.4. Check and adjustment of thermal gaps in the drive of valves
3.5. Adjustment of a tension of a chain of the drive of the camshaft
3.6. Removal of an uspokoitel of a chain of the drive of the camshaft
3.7. Removal of a natyazhitel of a chain of the drive of the camshaft
3.8. Removal of the camshaft and levers of the drive of valves
3.9. Replacement of maslootrazhatelny caps of the mechanism of gas distribution
3.10. Replacement of a forward epiploon of a bent shaft
3.11. Replacement of a back epiploon of a bent shaft
3.12. Removal of a gear wheel of the drive of the oil pump
3.13. Removal of a chain and asterisks of the drive of the camshaft
3.14. Removal of the roller of the drive of auxiliary units
3.15. Replacement of laying of an inlet pipe and final collector
3.16. Removal and dismantling of a head of the block of cylinders
3.17. Removal of the sensor of pressure of oil
3.18. Removal of an oil separator of system of ventilation of a case
3.19. Removal of support of the power unit on the car with the VAZ-2106 engine
3.20. Replacement of laying of the pallet of a case
3.21. Removal of the oil pump
3.22. Dismantling of the oil pump
3.23. Dismantle of conrod and piston group on the car
3.24. Removal of the engine from the car
3.25. Dismantling and assembly of the engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










3-2-zamena-masla.html

3.2. Oil replacement

We change oil on completely heated-up engine. Work is carried out on the elevator or a viewing ditch.

The stopper of a drain opening of the pallet of a case of the engine is located near a back cross-piece of a stretcher. That to turn off it, a working part of a regular six-sided key "on 12" for "Classical" engines VAZ should be reduced by 13-20 mm.

We turn off a case pallet stopper...

... also we merge oil in capacity not less than 4 l.

We merge oil within about 10 minutes and we wrap a drain stopper.

The stripper turned off an oil filter...

... also we remove it from the union.

We oil laying of the new filter engine, navorachivay and we tighten the filter on the union of the block of cylinders of the engine manually on 3/4 turns from the moment of contact of laying with the block of cylinders.

For oil filling...

... we uncover a maslozalivny mouth.

We fill in oil.

For control of amount of the filled-in oil...

... we take the oil level probe index from the directing tube.

Oil level on the probe has to be between tags of "min" and "max".

We launch the engine. When the control lamp of pressure of oil upon dashboards goes out, we stop the engine. We double-check the level of oil and if necessary we add.


"previous page
3.1. Description of a design
following page"
3.3. Replacement of laying of a cover of a head of the block of cylinders