Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
3.1. Description of a design
3.2. Oil replacement
3.3. Replacement of laying of a cover of a head of the block of cylinders
3.4. Check and adjustment of thermal gaps in the drive of valves
3.5. Adjustment of a tension of a chain of the drive of the camshaft
3.6. Removal of an uspokoitel of a chain of the drive of the camshaft
3.7. Removal of a natyazhitel of a chain of the drive of the camshaft
3.8. Removal of the camshaft and levers of the drive of valves
3.9. Replacement of maslootrazhatelny caps of the mechanism of gas distribution
3.10. Replacement of a forward epiploon of a bent shaft
3.11. Replacement of a back epiploon of a bent shaft
3.12. Removal of a gear wheel of the drive of the oil pump
3.13. Removal of a chain and asterisks of the drive of the camshaft
3.14. Removal of the roller of the drive of auxiliary units
3.15. Replacement of laying of an inlet pipe and final collector
3.16. Removal and dismantling of a head of the block of cylinders
3.17. Removal of the sensor of pressure of oil
3.18. Removal of an oil separator of system of ventilation of a case
3.19. Removal of support of the power unit on the car with the VAZ-2106 engine
3.20. Replacement of laying of the pallet of a case
3.21. Removal of the oil pump
3.22. Dismantling of the oil pump
3.23. Dismantle of conrod and piston group on the car
3.24. Removal of the engine from the car
3.25. Dismantling and assembly of the engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










3-20-zamena-prokladki-poddona-kartera.html

3.20. Replacement of laying of the pallet of a case

We perform work on a viewing ditch or the elevator.

We remove a forward cross-piece of a stretcher (see. "Removal of a stretcher").

By head "on 10" with the extender it is turned off 19 bolts of fastening of the pallet of a case to the block of cylinders of the engine.

We disconnect pillows of forward support of the power unit from arms of the block of cylinders (see. "Removal of support of the power unit on the car with the VAZ-2106 engine", page 46).

We establish an adjustable emphasis under a coupling case, as shown in a picture.

We bring a back part of the pallet of a case out of space between the block of cylinders of the engine and a back cross-piece of a stretcher and we remove the pallet together with sealing laying.

We remove laying of the pallet of a case.

We clear the privalenny planes of the block of cylinders and the pallet of a case of dirt, oil and the remains of old laying. We grease new laying with a thin layer of sealant and we install the case pallet in the return sequence. We tighten bolts of fastening of the pallet evenly ordered moment (see. "Appendix").


"previous page
3.19. Removal of support of the power unit on the car with the VAZ-2106 engine
following page"
3.21. Removal of the oil pump