Service of IZh 2126
1. General information
2. Engine UEPA-331
3. VAZ-2106 engine
4. Cooling system
5. Power supply system
6. Carburetor
7. System of ignition of the engine UEPA-331
7.1. Description of a design
7.2. Replacement of spark plugs
7.3. Removal of a cover and rotor of the distributor of ignition
7.4. Ignition distributor lubricant
7.5. Adjustment of the moment of ignition
7.6. Check and adjustment of a gap between contacts of the breaker
7.7. Removal of the distributor of ignition
7.8. Dismantling of the distributor of ignition
7.9. Removal of the condenser
7.10. Removal of the vacuum regulator of an advancing of ignition
7.11. Removal of a motionless plate of contact group of the breaker
7.12. Removal of the roller of the distributor
7.13. Removal of the coil of ignition
7.14. Councils of skilled
8. System of ignition of the VAZ-2106 engine
9. System of production of the fulfilled gases
10. Coupling
11. IZh-2126 transmission
12. VAZ-21074 transmission
13. Cardan transfer
14. Zadny Bridge
15. Forward suspension bracket
16. Back suspension bracket
17. Steering
18. Brake system
19. Electric equipment
20. Body
21. System of ventilation and heating
22. Features of a design of the IZh-2717 car
23. Appendix
24. Care of a car body
 










7-9-snyatie-kondensatora.html

7.9. Removal of the condenser

All operations on dismantle and installation of knots and details of the distributor of ignition, except removal of the roller of the distributor with the centrifugal regulator an ignition operezhniya, can be executed on the car. For descriptive reasons we show them on the removed distributor.

Removal of the condenser

We remove the condenser only for its replacement. We remove<плюсового> a wire tip from a contact bolt of the distributor<Снятие распределителя зажигания» (see).

We unscrew two screws of fastening of an arm of the condenser to the distributor case...

... also we remove the condenser.

We install the condenser in the return sequence.

Removal of the vacuum regulator of an advancing of ignition

We remove a cover and a rotor of the distributor<Снятие крышки и ротора распределителя зажигания» (see).

The tweezers removed a spring clamp of draft of the vacuum regulator from a pin of a mobile plate of contact group of the breaker.

We unscrew two screws of fastening of an arm of the vacuum regulator to the distributor case.

Having removed draft of the vacuum regulator from a pin of a mobile plate, we bring her out of the distributor case...

... also we remove the vacuum regulator.

We install the vacuum regulator in the return sequence.

Removal of a motionless plate of contact group of the breaker

We remove a cover and a rotor of the distributor<Снятие крышки и ротора распределителя зажигания» (see).

We remove the vacuum regulator of an advancing of ignition<Снятие вакуумного регулятора опережения зажигания» (see).

We remove contact group of the breaker<Проверка и регулировка зазора между контактами прерывателя» (see).

We unscrew the screw of fastening of a wire of "weight" and the holder of a motionless plate.

We take out the screw with a tip of a wire of "weight" and we remove the holder.

We unscrew the second screw located oppositely to the first...

... also we take out a motionless plate assembled with the bearing and a mobile plate.

We establish a motionless plate with the bearing in the return sequence.


"previous page
7.8. Dismantling of the distributor of ignition
following page"
7.10. Removal of the vacuum regulator of an advancing of ignition